Home
The SKAN HOLZ snow load extension consists of additional rafters that you mount between the existing roof rafters. This reduces the rafter spacing of the carport and increases the overall load-bearing capacity. The number and size of the rafters varies depending on the carport.The snow load increase raises the snow load of the carport to 2.5 kN/m².This snow load extension contains 6 additional rafters and is suitable for the following models:Emsland carport 402 (404) x 846 cmWendland carport 409 x 870 cmColour-treated in whitePlease note:The snow load cannot be retrofitted to the carports. Please check the snow load limit required in your residential area before assembly.ConstructionThe construction is made of glued laminate timber, consisting of several dried layers, attached to one another with finger-jointing. They are glued onto one another for weather-resistance. This results in a load-bearing beam which is more resistant to warping and less prone to fissures than naturally grown wood.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Snow load increase to sk=2.50 kN/m²Glued laminated timber, Colour-treated in whiteSuitable for Emsland carport 402 (404) x 846 cmSuitable for Wendland carport 409 x 870 cm
delivery time: 4-5 weeks
Rear wall made of siding for installation in a SKAN HOLZ carportSiding consists of two layers of loose 20 mm thick formwork boards, which are only attached once the carport is fully assembled. It provides increased stability, privacy from the side and protection from e.g. wind or overgrown hedges.Product featuresWidth: 352 cmHeight: 220 cmFormwork thickness: 2 x 12 cmH-post anchor includedMaterial: Nordic spruceColour-treated in slate greyPhoto galleryAny carports, colour treatment and decoration shown are not included in the scope of delivery. These are customer photos, which are intended to give you an impression of the installed state.ConstructionThe construction is made of solid Nordic fir. We use technically-dried, solid spruce wood, scanned for flaws, sorted and weatherproofed by finger-joint bonding according to length. Small fissures, branches and slight twists reflect the character of the materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.incl. installation post and post anchor352 x 220 cmSpruce, colour-treated in slate greyincl. installation post with post anchor
delivery time: 4-5 weeks
The SKAN HOLZ snow load extension consists of additional rafters that you mount between the existing roof rafters. This reduces the rafter spacing of the carport and increases the overall load-bearing capacity. The number and size of the rafters varies depending on the carport.The snow load increase raises the snow load of the carport to 2.5 kN/m².This snow load extension contains 6 additional rafters and is suitable for the following models:Emsland carport 402 (404) x 846 cmWendland carport 409 x 870 cmColour-treated in slate greyPlease note:The snow load cannot be retrofitted to the carports. Please check the snow load limit required in your residential area before assembly.ConstructionThe construction is made of glued laminate timber, consisting of several dried layers, attached to one another with finger-jointing. They are glued onto one another for weather-resistance. This results in a load-bearing beam which is more resistant to warping and less prone to fissures than naturally grown wood.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Snow load increase to sk=2.50 kN/m²Glued laminated timber, colour-treated in slate greySuitable for Emsland carport 402 (404) x 846 cmSuitable for Wendland carport 409 x 870 cm
delivery time: 4-5 weeks
Weather-resistant metal gutter set.suited to the gazebo Orleans 4Colour: anthracite coateddiameter gutter 100 mmdiameter downpipe 75 mmconsisting of :gutter(s)downpipeconnection elementsgutter end piecespipe clampsgutter bracketsdownpipe bendscrews for gutter bracketssilicone cartridge for sealingEasy insertion and clamping of parts, one-time gluing of gutter end pieces, no soldering nor welding.Metal gutter setAnthraciteDiameter gutter 100 mmDiameter downpipe 75 mm
delivery time: 3-4 weeks
Lateral canopy 168 x 169 cm for SKAN HOLZ CrossCube houses Sydney and Brisbane 2.The facing of the canopy consists of 10 mm-thick, painted cladding panels (exterior colour-finished) with slate-grey wood-frame structure.Boarding of 19 mm-thick wood moulding is covered with aluminium-coated, self-adhesive roof sheeting. The pitch runs toward the back.wall colour: Slate grey (RAL 7015)Building kit complete with mounting material and assembly instructions.Gutter extension optionally available.Tug-on roof for CrossCube, Size 2168 x 169 cmWall colour: Slate grey (RAL 7015)Including self-adhesive KSK-M foil
delivery time: 3-4 weeks
Lateral canopy 168 x 169 cm for SKAN HOLZ CrossCube houses Perth and Melbourne 2.The facing of the canopy consists of 10 mm-thick, painted cladding panels (exterior colour-finished) with slate-grey wood-frame structure.Boarding of 19 mm-thick wood moulding is covered with aluminium-coated, self-adhesive roof sheeting. The pitch runs toward the back.wall colour: Telegrey (RAL 7047)Building kit complete with mounting material and assembly instructions.Gutter extension optionally available.Tug-on roof for CrossCube, Size 2168 x 169 cmWall colour: Telegrey (RAL 7047)Including self-adhesive KSK-M foil
delivery time: 3-4 weeks
Carport double doorexterior frame dimensions: 148 x 198 cmwith stopper on the rightmoulded cylinder lock with 3 keysincluding door-handle set and mounting materialdoor clear opening: 136,5 x 192 cmMaterial: nordic sprucecolour-treated in anthraciteDouble door for carportsExterior frame dimensions: 148 x 198 cmAperture dimensions: 136,5 x 192 cmColour-treated in anthracite
delivery time: 4-5 weeks
Carport double doorexterior frame dimensions: 148 x 198 cmwith stopper on the rightmoulded cylinder lock with 3 keysincluding door-handle set and mounting materialdoor clear opening: 136,5 x 192 cmMaterial: nordic sprucecolour-treated in slate greyDouble door for carportsExterior frame dimensions: 148 x 198 cmAperture dimensions: 136,5 x 192 cmColour-treated in slate grey
delivery time: 4-5 weeks
Carport double doorexterior frame dimensions: 148 x 198 cmwith stopper on the rightmoulded cylinder lock with 3 keysincluding door-handle set and mounting materialdoor clear opening: 136,5 x 192 cmMaterial: nordic sprucecolour-treated in whiteDouble door for carportsExterior frame dimensions: 148 x 198 cmAperture dimensions: 136,5 x 192 cmColour-treated in white
delivery time: 4-5 weeks
Rear wall made of siding for installation in a SKAN HOLZ carportSiding consists of two layers of loose 20 mm thick formwork boards, which are only attached once the carport is fully assembled. It provides increased stability, privacy from the side and protection from e.g. wind or overgrown hedges.Product featuresWidth: 362 cmHeight: 330 cmFormwork thickness: 2 x 12 cmBuilt-in posts 12 x 12 cm, glulam spruceIncluding H-post anchorMaterial: Nordic spruceUntreated in colourPhoto galleryAny carports, colour treatment and decoration shown are not included in the scope of delivery. These are customer photos, which are intended to give you an impression of the installed state.ConstructionThe construction is made of solid Nordic fir. We use technically-dried, solid spruce wood, scanned for flaws, sorted and weatherproofed by finger-joint bonding according to length. Small fissures, branches and slight twists reflect the character of the materials used.Colour treatmentThis kit is supplied untreated in color. This gives you the option to paint the surfaces according to your own design preferences and to match them to their surroundings.As timber used outdoors is exposed to the elements, a suitable protective coat is recommended. To ensure the treatment is as even as possible, the first coat should be applied to all sides of the timber components before assembly. Suitable wood protection products may be used for this purpose in accordance with the manufacturer’s instructions.To preserve the appearance of the wood in the long term, regular care and maintenance are advisable. The required maintenance intervals depend, amongst other things, on the location, weather conditions and the chosen coating. Please follow the relevant application and care instructions provided by the manufacturers of the products used.Rear wall made of sidingSpruce, untreatedHeight 330 cmInstallation posts 12 x 12 cm (glulam spruce)H-post anchor included
delivery time: 3-4 weeks
Side wall made of siding for installation in a SKAN HOLZ carportSiding consists of two layers of loose 20 mm thick formwork boards, which are only attached once the carport is fully assembled. It provides increased stability, privacy from the side and protection from e.g. wind or overgrown hedges.Product featuresWidth: 230 cmHeight: 330 cmFormwork thickness: 2 x 12 cmMaterial: Nordic spruceColour-treated in whitePhoto galleryAny carports, colour treatment and decoration shown are not included in the scope of delivery. These are customer photos, which are intended to give you an impression of the installed state.ConstructionThe construction is made of solid Nordic fir. We use technically-dried, solid spruce wood, scanned for flaws, sorted and weatherproofed by finger-joint bonding according to length. Small fissures, branches and slight twists reflect the character of the materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Side wall made of sidingNordic spruceColour-treated in whiteInstallation height 330 cmInstallation width 230 cm
delivery time: 3-4 weeks
Side wall made of siding for installation in a SKAN HOLZ carportSiding consists of two layers of loose 20 mm thick formwork boards, which are only attached once the carport is fully assembled. It provides increased stability, privacy from the side and protection from e.g. wind or overgrown hedges.Product featuresWidth: 230 cmHeight: 330 cmFormwork thickness: 2 x 12 cmMaterial: Nordic spruceColour-treated in anthracitePhoto galleryAny carports, colour treatment and decoration shown are not included in the scope of delivery. These are customer photos, which are intended to give you an impression of the installed state.ConstructionThe construction is made of solid Nordic fir. We use technically-dried, solid spruce wood, scanned for flaws, sorted and weatherproofed by finger-joint bonding according to length. Small fissures, branches and slight twists reflect the character of the materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Side wall made of sidingNordic spruceColour-treated in anthraciteInstallation height 330 cmInstallation width 230 cm
delivery time: 3-4 weeks
Side wall made of siding for installation in a SKAN HOLZ carportSiding consists of two layers of loose 20 mm thick formwork boards, which are only attached once the carport is fully assembled. It provides increased stability, privacy from the side and protection from e.g. wind or overgrown hedges.Product featuresWidth: 230 cmHeight: 330 cmFormwork thickness: 2 x 12 cmMaterial: Nordic spruceColour-treated in slate greyPhoto galleryAny carports, colour treatment and decoration shown are not included in the scope of delivery. These are customer photos, which are intended to give you an impression of the installed state.ConstructionThe construction is made of solid Nordic fir. We use technically-dried, solid spruce wood, scanned for flaws, sorted and weatherproofed by finger-joint bonding according to length. Small fissures, branches and slight twists reflect the character of the materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Side wall made of sidingNordic spruceColour-treated in slate greyInstallation height 330 cmInstallation width 230 cm
delivery time: 3-4 weeks
The decorative SKAN HOLZ balustrade with solid St. Andrew's crosses of solid structural timber is suited to SKAN HOLZ gazebos of glued laminate timber with post spacing of 465 cm.Product featuresWidth: 465 cmHeight: 84 cm (+arbitrary distance form floor)thickness cross beams: 10 x 10 cmthickness St. Andrew`s cross: 8 x 8 cmthickness posts: 12 x 12 cmincluding mounting bracketsincluding post cover capMaterial: sprucecolour-treated in light oakPhoto galleryAny illustrated terrace roofs, colour treatment and decoration are not included in scope of supply. This involves customer photos, which are to provide you with an impression of the installed condition.ConstructionThe construction is made of KVH solid construction timber. KVH is a designation for technically-dried, continuously bonded, solid spruce wood. The individual wood parts are dried, scanned for flaws, sorted and then weatherproofed by continuous bonding using finger-jointing. Fissures, branches and slight twists reflect the character of the materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Balustrade St.Andrew`s crossSuitable for post spacing of 465 cmNordic spruceColour-treated in light oak
delivery time: 4-5 weeks
The decorative SKAN HOLZ sidewall with solid St. Andrew's crosses of solid structural timber is suited to SKAN HOLZ terrace roofs of glued laminate with a depth of 250cm and 239cm (wall mounting).Product featuresWidth: 205 cmHeight: 210 cm (+arbitrary distance form floor)thickness cross beams: 10 x 10 cmthickness St. Andrew`s cross: 8 x 8 cmthickness posts: 12 x 12 cmincluding mounting bracket(s)Material: sprucecolour-treated in light oakPhoto galleryAny illustrated terrace roofs, colour treatment and decoration are not included in scope of supply. This involves customer photos, which are to provide you with an impression of the installed condition.ConstructionThe construction is made of KVH solid construction timber. KVH is a designation for technically-dried, continuously bonded, solid spruce wood. The individual wood parts are dried, scanned for flaws, sorted and then weatherproofed by continuous bonding using finger-jointing. Fissures, branches and slight twists reflect the character of the materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Sidewall (wall mounting)St.Andrew`s cross, nordic spruceSuitable for terrace roofs with a depth of 250 cmColour-treated in light oak
delivery time: 4-5 weeks