Home
Rear wall made of siding for installation in a SKAN HOLZ carportSiding consists of two layers of loose 20 mm thick formwork boards, which are only attached once the carport is fully assembled. It provides increased stability, privacy from the side and protection from e.g. wind or overgrown hedges.Product featuresWidth: 352 cmHeight: 220 cmFormwork thickness: 2 x 12 cmH-post anchor includedMaterial: Nordic spruceColour-treated in walnutPhoto galleryAny carports, colour treatment and decoration shown are not included in the scope of delivery. These are customer photos, which are intended to give you an impression of the installed state.ConstructionThe construction is made of solid Nordic fir. We use technically-dried, solid spruce wood, scanned for flaws, sorted and weatherproofed by finger-joint bonding according to length. Small fissures, branches and slight twists reflect the character of the materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.incl. installation post and post anchor352 x 220 cmSpruce, colour-treated in walnutincl. installation post with post anchor
delivery time: 4-5 weeks
The SKAN HOLZ snow load extension consists of additional rafters that you mount between the existing roof rafters. This reduces the rafter spacing of the carport and increases the overall load-bearing capacity. The number and size of the rafters varies depending on the carport.The snow load increase raises the snow load of the carport to 2.5 kN/m².This snow load extension contains 6 additional rafters and is suitable for the following models:Emsland carport 402 (404) x 846 cmWendland carport 409 x 870 cmColour-treated in walnutPlease note:The snow load cannot be retrofitted to the carports. Please check the snow load limit required in your residential area before assembly.ConstructionThe construction is made of glued laminate timber, consisting of several dried layers, attached to one another with finger-jointing. They are glued onto one another for weather-resistance. This results in a load-bearing beam which is more resistant to warping and less prone to fissures than naturally grown wood.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Snow load increase to sk=2.50 kN/m²Glued laminated timber, colour-treated in walnutSuitable for Emsland carport 402 (404) x 846 cmSuitable for Wendland carport 409 x 870 cm
delivery time: 4-5 weeks
Rear wall made of siding for installation in a SKAN HOLZ carportSiding consists of two layers of loose 20 mm thick formwork boards, which are only attached once the carport is fully assembled. It provides increased stability, privacy from the side and protection from e.g. wind or overgrown hedges.Product featuresWidth: 352 cmHeight: 220 cmFormwork thickness: 2 x 12 cmH-post anchor includedMaterial: Nordic spruceColour-treated in light oakPhoto galleryAny carports, colour treatment and decoration shown are not included in the scope of delivery. These are customer photos, which are intended to give you an impression of the installed state.ConstructionThe construction is made of solid Nordic fir. We use technically-dried, solid spruce wood, scanned for flaws, sorted and weatherproofed by finger-joint bonding according to length. Small fissures, branches and slight twists reflect the character of the materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.incl. installation post and post anchor352 x 220 cmSpruce, colour-treated in light oakincl. installation post with post anchor
delivery time: 4-5 weeks
The practical SKAN HOLZ sidewall of solid structural timber with 10 mm-thick Polycarbonate sheet is suited to free-standing SKAN HOLZ terrace roofs (wall mounting) of glued laminate with a depth of 400cm and 389cm.Product featuresWidth: 355 cmHeight: 200 cm (including distance form floor)thickness cross-bar: 6 x 6 cmthickness Polycarbonate sheet: 10 mmAluminium profile including EPDM lip-sealsMaterial: sprucecolour-treated in walnutPhoto galleryAny illustrated terrace roofs, colour treatment and decoration are not included in scope of supply. This involves customer photos, which are to provide you with an impression of the installed condition.ConstructionThe construction is made of KVH solid construction timber. KVH is a designation for technically-dried, continuously bonded, solid spruce wood. The individual wood parts are dried, scanned for flaws, sorted and then weatherproofed by continuous bonding using finger-jointing. Fissures, branches and slight twists reflect the character of the materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Sidewall with polycarbonate sheetSuitable for wall mounting terrace roofsSuitable for a depth of 389 and 400 cmColour-treated in walnut
delivery time: 4-5 weeks
The practical SKAN HOLZ sidewall of solid structural timber with 10 mm-thick Polycarbonate sheet is suited to free-standing SKAN HOLZ terrace roofs (wall mounting) of glued laminate with a depth of 400cm and 389cm.Product featuresWidth: 355 cmHeight: 200 cm (including distance form floor)thickness cross-bar: 6 x 6 cmthickness Polycarbonate sheet: 10 mmAluminium profile including EPDM lip-sealsMaterial: sprucecolour-treated in light oakPhoto galleryAny illustrated terrace roofs, colour treatment and decoration are not included in scope of supply. This involves customer photos, which are to provide you with an impression of the installed condition.ConstructionThe construction is made of KVH solid construction timber. KVH is a designation for technically-dried, continuously bonded, solid spruce wood. The individual wood parts are dried, scanned for flaws, sorted and then weatherproofed by continuous bonding using finger-jointing. Fissures, branches and slight twists reflect the character of the materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Sidewall with polycarbonate sheetSuitable for wall mounting terrace roofsSuitable for a depth of 389 and 400 cmColour-treated in light oak
delivery time: 4-5 weeks
SKAN HOLZ Rhombus Back Panel for CarportsThe Rhombus rear panel from SKAN HOLZ is a practical and visually appealing addition to selected carports. It provides additional privacy and gives the carport a modern, open rhombus design. The panel is constructed from individual rhombus-shaped profile strips, which are fitted between the existing posts.The product is available in various sizes and colour options and can be selected to match the specific carport. Made from Nordic spruce, the back panel impresses with its natural appearance and solid workmanship.Product featuresRhombus rear panel for retrofitting or adding to selected SKAN HOLZ carportsAvailable in various sizes and colour finishesModern rhombus design with an airy lookComprises individual rhombus-shaped profile strips to be screwed between the postsMade from Nordic spruceProvides additional privacy and wind protectionComplements the harmonious overall look of the carportContentsRhombus-shaped profile strips 2.8 x 5.6 cmPosts 12 x 12 cm60 cm H-post anchors made of galvanised flat steel for embedding in point foundations to be provided on siteAssembly materialsNotesAny carports, colour finishes, accessories or decorative items shown are not included in the scope of delivery. Illustrations may show examples of use and are intended to illustrate the assembled state. The scope of delivery is determined by the specific product variant selected.ConstructionThe construction is made of solid Nordic fir. We use technically-dried, solid spruce wood, scanned for flaws, sorted and weatherproofed by finger-joint bonding according to length. Small fissures, branches and slight twists reflect the character of the materials used.Colour treatmentThis kit is supplied untreated in color. This gives you the option to paint the surfaces according to your own design preferences and to match them to their surroundings.As timber used outdoors is exposed to the elements, a suitable protective coat is recommended. To ensure the treatment is as even as possible, the first coat should be applied to all sides of the timber components before assembly. Suitable wood protection products may be used for this purpose in accordance with the manufacturer’s instructions.To preserve the appearance of the wood in the long term, regular care and maintenance are advisable. The required maintenance intervals depend, amongst other things, on the location, weather conditions and the chosen coating. Please follow the relevant application and care instructions provided by the manufacturers of the products used.Backwall RhombusSuitable for post spacing of 550 cmNordic sprucenot Colour-treatedProvides additional privacy and protection from the wind
delivery time: 3-4 weeks
Backwall of profiled siding material for installation under a SKAN HOLZ carportProfiled siding consists of loose tongued and grooved timber in 20 mm thickness, which is attached to one another and mounted between the posts.Product featuresWidth: 550 cmHeight: 200 cmThickness: 20 mmincluding post 9 x 9 cmincluding H-post anchorMaterial: sprucecolour-treated in slate greyConstructionThe construction is made of impregnated softwood. Spruce and pine wood, which is not technically-dried, acquires its greenish color from metal salts released by the impregnating agent. They protect wood against fungus and insect infestations, but do not contain UV protection. Impregnation gives wood higher residual moisture. Subsequent drying can lead to release of resin, twisting and formation of drying cracks, which pose no static disadvantage and rather reflect the natural materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Backwall in profiled siding materialSuitable for post spacing of 550 cmProfiled siding materialColour-treated in slate grey
delivery time: 4-5 weeks
Carport double doorexterior frame dimensions: 148 x 198 cmwith stopper on the rightmoulded cylinder lock with 3 keysincluding door-handle set and mounting materialdoor clear opening: 136,5 x 192 cmMaterial: nordic sprucecolour-treated in light oakDouble door for carportsExterior frame dimensions: 148 x 198 cmAperture dimensions: 136,5 x 192 cmColour-treated in light oak
delivery time: 4-5 weeks
Carport double doorexterior frame dimensions: 148 x 198 cmwith stopper on the rightmoulded cylinder lock with 3 keysincluding door-handle set and mounting materialdoor clear opening: 136,5 x 192 cmMaterial: nordic sprucecolour-treated in walnutDouble door for carportsExterior frame dimensions: 148 x 198 cmAperture dimensions: 136,5 x 192 cmColour-treated in walnut
delivery time: 4-5 weeks
The SKAN HOLZ snow load extension consists of additional rafters that you mount between the existing roof rafters. This reduces the rafter spacing of the carport and increases the overall load-bearing capacity. The number and size of the rafters varies depending on the carport.The snow load increase raises the snow load of the carport to 2.0 kN/m².This snow load increase contains 10 additional rafters and fits the following models:Friesland carport 546 x 860 cmFriesland carport 557 x 860 cmGreen impregnatedPlease note:The snow load extension cannot be retrofitted to the carports. Please check the snow load limit required in your residential area before assembly.ConstructionThe construction is made of impregnated softwood. Spruce and pine wood, which is not technically-dried, acquires its greenish color from metal salts released by the impregnating agent. They protect wood against fungus and insect infestations, but do not contain UV protection. Impregnation gives wood higher residual moisture. Subsequent drying can lead to release of resin, twisting and formation of drying cracks, which pose no static disadvantage and rather reflect the natural materials used.Colour treatmentThe wooden parts in this kit have been treated at the factory with a water-based preservative. This means the kit can be assembled straight away upon delivery. To ensure the long-term preservation of the wooden surface, it is recommended that the wood be treated further after a sufficient drying and weathering period of approximately 2 to 3 sunny months.Before painting, the surface should be lightly sanded and cleaned. It is then recommended to apply two coats of a wood preservative suitable for outdoor use. Products with UV protection can help to reduce the visual ageing of the wood caused by weathering. Please follow the application instructions provided by the respective manufacturer.Regular maintenance and timely re-treatment help to keep the surface in good condition over the long term. The required maintenance intervals depend on the location, exposure to the elements and the coating system used.Snow load increase to sk=2.00 kN/m²Suitable for Friesland carport 546 x 860 cmSuitable for Friesland carport 557 x 860 cmGreen impregnatedMust be installed during carport assembly
delivery time: 3-4 weeks
The SKAN HOLZ snow load extension consists of additional rafters that you mount between the existing roof rafters. This reduces the rafter spacing of the carport and increases the overall load-bearing capacity. The number and size of the rafters varies depending on the carport.The snow load increase raises the snow load of the carport to 2.0 kN/m².This snow load increase contains 10 additional rafters and is suitable for the following models:Spreewald carport 585 x 893 cmGreen impregnatedPlease note:The snow load increase cannot be retrofitted to the carports. Please check the snow load limit required in your residential area before assembly.ConstructionThe construction is made of impregnated softwood. Spruce and pine wood, which is not technically-dried, acquires its greenish color from metal salts released by the impregnating agent. They protect wood against fungus and insect infestations, but do not contain UV protection. Impregnation gives wood higher residual moisture. Subsequent drying can lead to release of resin, twisting and formation of drying cracks, which pose no static disadvantage and rather reflect the natural materials used.Colour treatmentThe wooden parts in this kit have been treated at the factory with a water-based preservative. This means the kit can be assembled straight away upon delivery. To ensure the long-term preservation of the wooden surface, it is recommended that the wood be treated further after a sufficient drying and weathering period of approximately 2 to 3 sunny months.Before painting, the surface should be lightly sanded and cleaned. It is then recommended to apply two coats of a wood preservative suitable for outdoor use. Products with UV protection can help to reduce the visual ageing of the wood caused by weathering. Please follow the application instructions provided by the respective manufacturer.Regular maintenance and timely re-treatment help to keep the surface in good condition over the long term. The required maintenance intervals depend on the location, exposure to the elements and the coating system used.Snow load increase to sk=2.00 kN/m²Suitable for Spreewald carport 585 x 893 cmGreen impregnatedMust be installed during carport assembly
delivery time: 3-4 weeks
The practical SKAN HOLZ sidewall of solid structural timber with 10 mm-thick Polycarbonate sheet is suited to free-standing SKAN HOLZ terrace roofs (wall mounting) of glued laminate with a depth of 400cm and 389cm.Product featuresWidth: 355 cmHeight: 200 cm (including distance form floor)thickness cross-bar: 6 x 6 cmthickness Polycarbonate sheet: 10 mmAluminium profile including EPDM lip-sealsMaterial: sprucecolour-treated in slate greyPhoto galleryAny illustrated terrace roofs, colour treatment and decoration are not included in scope of supply. This involves customer photos, which are to provide you with an impression of the installed condition.ConstructionThe construction is made of KVH solid construction timber. KVH is a designation for technically-dried, continuously bonded, solid spruce wood. The individual wood parts are dried, scanned for flaws, sorted and then weatherproofed by continuous bonding using finger-jointing. Fissures, branches and slight twists reflect the character of the materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Sidewall with polycarbonate sheetSuitable for wall mounting terrace roofsSuitable for a depth of 389 and 400 cmColour-treated in slate grey
delivery time: 4-5 weeks
The practical SKAN HOLZ sidewall of solid structural timber with 10 mm-thick Polycarbonate sheet is suited to free-standing SKAN HOLZ terrace roofs (wall mounting) of glued laminate with a depth of 400cm and 389cm.Product featuresWidth: 355 cmHeight: 200 cm (including distance form floor)thickness cross-bar: 6 x 6 cmthickness Polycarbonate sheet: 10 mmAluminium profile including EPDM lip-sealsMaterial: sprucecolour-treated in anthracitePhoto galleryAny illustrated terrace roofs, colour treatment and decoration are not included in scope of supply. This involves customer photos, which are to provide you with an impression of the installed condition.ConstructionThe construction is made of KVH solid construction timber. KVH is a designation for technically-dried, continuously bonded, solid spruce wood. The individual wood parts are dried, scanned for flaws, sorted and then weatherproofed by continuous bonding using finger-jointing. Fissures, branches and slight twists reflect the character of the materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Sidewall with polycarbonate sheetSuitable for wall mounting terrace roofsSuitable for a depth of 389 and 400 cmColour-treated in anthracite
delivery time: 4-5 weeks
The practical SKAN HOLZ sidewall of solid structural timber with 10 mm-thick Polycarbonate sheet is suited to free-standing SKAN HOLZ terrace roofs (wall mounting) of glued laminate with a depth of 400cm and 389cm.Product featuresWidth: 355 cmHeight: 200 cm (including distance form floor)thickness cross-bar: 6 x 6 cmthickness Polycarbonate sheet: 10 mmAluminium profile including EPDM lip-sealsMaterial: sprucecolour-treated in whitePhoto galleryAny illustrated terrace roofs, colour treatment and decoration are not included in scope of supply. This involves customer photos, which are to provide you with an impression of the installed condition.ConstructionThe construction is made of KVH solid construction timber. KVH is a designation for technically-dried, continuously bonded, solid spruce wood. The individual wood parts are dried, scanned for flaws, sorted and then weatherproofed by continuous bonding using finger-jointing. Fissures, branches and slight twists reflect the character of the materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Sidewall with polycarbonate sheetSuitable for wall mounting terrace roofsSuitable for a depth of 389 and 400 cmColour-treated in white
delivery time: 4-5 weeks
Side wall made of siding for installation in a SKAN HOLZ carportSiding consists of two layers of loose 20 mm thick formwork boards, which are only attached once the carport is fully assembled. It provides increased stability, privacy from the side and protection from e.g. wind or overgrown hedges.Product featuresWidth: 230 cmHeight: 330 cmFormwork thickness: 2 x 12 cmMaterial: Nordic spruceColour-treated in walnutPhoto galleryAny carports, colour treatment and decoration shown are not included in the scope of delivery. These are customer photos, which are intended to give you an impression of the installed state.ConstructionThe construction is made of solid Nordic fir. We use technically-dried, solid spruce wood, scanned for flaws, sorted and weatherproofed by finger-joint bonding according to length. Small fissures, branches and slight twists reflect the character of the materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Side wall made of sidingNordic spruceColour-treated in walnutInstallation height 330 cmInstallation width 230 cm
delivery time: 3-4 weeks
Side wall made of siding for installation in a SKAN HOLZ carportSiding consists of two layers of loose 20 mm thick formwork boards, which are only attached once the carport is fully assembled. It provides increased stability, privacy from the side and protection from e.g. wind or overgrown hedges.Product featuresWidth: 230 cmHeight: 330 cmFormwork thickness: 2 x 12 cmMaterial: Nordic spruceColour-treated in light oakPhoto galleryAny carports, colour treatment and decoration shown are not included in the scope of delivery. These are customer photos, which are intended to give you an impression of the installed state.ConstructionThe construction is made of solid Nordic fir. We use technically-dried, solid spruce wood, scanned for flaws, sorted and weatherproofed by finger-joint bonding according to length. Small fissures, branches and slight twists reflect the character of the materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Side wall made of sidingNordic spruceColour-treated in light oakInstallation height 330 cmInstallation width 230 cm
delivery time: 3-4 weeks
The decorative SKAN HOLZ balustrade with solid St. Andrew's crosses of solid structural timber is suited to SKAN HOLZ gazebos of glued laminate timber with post spacing of 400 cm.Product featuresWidth: 400 cmHeight: 84 cm (+arbitrary distance form floor)thickness cross beams: 10 x 10 cmthickness St. Andrew`s cross: 8 x 8 cmthickness posts: 12 x 12 cmincluding mounting bracketsincluding post cover capMaterial: sprucecolour-treated in anthracitePhoto galleryAny illustrated terrace roofs, colour treatment and decoration are not included in scope of supply. This involves customer photos, which are to provide you with an impression of the installed condition.ConstructionThe construction is made of KVH solid construction timber. KVH is a designation for technically-dried, continuously bonded, solid spruce wood. The individual wood parts are dried, scanned for flaws, sorted and then weatherproofed by continuous bonding using finger-jointing. Fissures, branches and slight twists reflect the character of the materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Balustrade St.Andrew`s crossSuitable for post spacing of 400 cmNordic spruceColour-treated in anthracite
delivery time: 4-5 weeks
The decorative SKAN HOLZ balustrade with solid St. Andrew's crosses of solid structural timber is suited to SKAN HOLZ gazebos of glued laminate timber with post spacing of 400 cm.Product featuresWidth: 400 cmHeight: 84 cm (+arbitrary distance form floor)thickness cross beams: 10 x 10 cmthickness St. Andrew`s cross: 8 x 8 cmthickness posts: 12 x 12 cmincluding mounting bracketsincluding post cover capMaterial: sprucecolour-treated in slate greyPhoto galleryAny illustrated terrace roofs, colour treatment and decoration are not included in scope of supply. This involves customer photos, which are to provide you with an impression of the installed condition.ConstructionThe construction is made of KVH solid construction timber. KVH is a designation for technically-dried, continuously bonded, solid spruce wood. The individual wood parts are dried, scanned for flaws, sorted and then weatherproofed by continuous bonding using finger-jointing. Fissures, branches and slight twists reflect the character of the materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Balustrade St.Andrew`s crossSuitable for post spacing of 400 cmNordic spruceColour-treated in slate grey
delivery time: 4-5 weeks
The decorative SKAN HOLZ balustrade with solid St. Andrew's crosses of solid structural timber is suited to SKAN HOLZ gazebos of glued laminate timber with post spacing of 400 cm.Product featuresWidth: 400 cmHeight: 84 cm (+arbitrary distance form floor)thickness cross beams: 10 x 10 cmthickness St. Andrew`s cross: 8 x 8 cmthickness posts: 12 x 12 cmincluding mounting bracketsincluding post cover capMaterial: sprucecolour-treated in whitePhoto galleryAny illustrated terrace roofs, colour treatment and decoration are not included in scope of supply. This involves customer photos, which are to provide you with an impression of the installed condition.ConstructionThe construction is made of KVH solid construction timber. KVH is a designation for technically-dried, continuously bonded, solid spruce wood. The individual wood parts are dried, scanned for flaws, sorted and then weatherproofed by continuous bonding using finger-jointing. Fissures, branches and slight twists reflect the character of the materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Balustrade St.Andrew`s crossSuitable for post spacing of 400 cmNordic spruceColour-treated in white
delivery time: 4-5 weeks
The decorative SKAN HOLZ sidewall with solid St. Andrew's crosses of Douglas fir is suited to SKAN HOLZ terrace roofs of Douglas fir with a depth 300 cm.Product featuresWidth: 255 cmHeight: 210 cmthickness cross beams: 10 x 10 cmthickness St. Andrew`s cross: 8 x 8 cmthickness posts: 12 x 12 cmincluding mounting bracket(s)Material: douglas firnot colour-treatedPhoto galleryAny illustrated terrace roofs, colour treatment and decoration are not included in scope of supply. This involves customer photos, which are to provide you with an impression of the installed condition.ConstructionThe construction is made of Douglas fir. The reddish heart wood of the Douglas fir contains resin and oils that are resistant against fungus and insect infestations. We use technically-dried Douglas fir which, depending on length, is partly weatherproofed by finger jointing. This type of wood features high surface hardness. Fissures, branches and twists reflect the natural materials used.If Douglas fir is not treated with varnish, a glossy grey-silver patina forms over time. It protects the built structure from environmental challenges, and you from time-consuming wood maintenance.Colour treatmentThe wooden parts in this kit are supplied untreated in color. Douglas fir can be used without chemical wood preservative. When used outdoors, the wood develops a natural patina over time due to weathering, which can be maintained by regular cleaning with water.If you wish to preserve the original colour and texture of the wood for as long as possible, you should treat the wooden surfaces with a suitable coating system. We recommend applying a coat of paint to all sides before assembly. Please follow the manufacturer’s instructions for application. Depending on exposure to the elements and the condition of the surface, it may be necessary to reapply the paint regularly to maintain the wood’s appearance.Sidewall St.Andrew`s crossSuitable for terrace roofs with a depth of 300 cmdouglas firnot Colour-treated
delivery time: 3-4 weeks
Rear wall made of siding for installation in a SKAN HOLZ carportSiding consists of two layers of loose 20 mm thick formwork boards, which are only attached once the carport is fully assembled. It provides increased stability, privacy from the side and protection from e.g. wind or overgrown hedges.Product featuresWidth: 352 cmHeight: 220 cmFormwork thickness: 2 x 12 cmH-post anchor includedMaterial: Nordic spruceColour-treated in anthracitePhoto galleryAny carports, colour treatment and decoration shown are not included in the scope of delivery. These are customer photos, which are intended to give you an impression of the installed state.ConstructionThe construction is made of solid Nordic fir. We use technically-dried, solid spruce wood, scanned for flaws, sorted and weatherproofed by finger-joint bonding according to length. Small fissures, branches and slight twists reflect the character of the materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.incl. installation post and post anchor352 x 220 cmSpruce, colour-treated in anthraciteincl. installation post with post anchor
delivery time: 4-5 weeks
The SKAN HOLZ snow load extension consists of additional rafters that you mount between the existing roof rafters. This reduces the rafter spacing of the carport and increases the overall load-bearing capacity. The number and size of the rafters varies depending on the carport.The snow load increase raises the snow load of the carport to 2.5 kN/m².This snow load extension contains 6 additional rafters and is suitable for the following models:Emsland carport 402 (404) x 846 cmWendland carport 409 x 870 cmColour-treated in anthracitePlease note:The snow load cannot be retrofitted to the carports. Please check the snow load limit required in your residential area before assembly.ConstructionThe construction is made of glued laminate timber, consisting of several dried layers, attached to one another with finger-jointing. They are glued onto one another for weather-resistance. This results in a load-bearing beam which is more resistant to warping and less prone to fissures than naturally grown wood.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Snow load increase to sk=2.50 kN/m²Glued laminated timber, colour-treated in anthraciteSuitable for Emsland carport 402 (404) x 846 cmSuitable for Wendland carport 409 x 870 cm
delivery time: 4-5 weeks
Rear wall made of siding for installation in a SKAN HOLZ carportSiding consists of two layers of loose 20 mm thick formwork boards, which are only attached once the carport is completely assembled. It provides increased stability, privacy from the side and protection from e.g. wind or overgrown hedges.Product featuresWidth: 352 cmHeight: 220 cmFormwork thickness: 2 x 12 cmH-post anchor includedMaterial: Nordic spruceColour-treated in whitePhoto galleryAny carports, colour treatment and decoration shown are not included in the scope of delivery. These are customer photos, which are intended to give you an impression of the installed state.ConstructionThe construction is made of solid Nordic fir. We use technically-dried, solid spruce wood, scanned for flaws, sorted and weatherproofed by finger-joint bonding according to length. Small fissures, branches and slight twists reflect the character of the materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.incl. installation post and post anchor352 x 220 cmSpruce, Colour-treated in whiteincl. installation post with post anchor
delivery time: 4-5 weeks