Home
SKAN HOLZ Rhombus Back Panel for CarportsThe Rhombus rear panel from SKAN HOLZ is a practical and visually appealing addition to selected carports. It provides additional privacy and gives the carport a modern, open rhombus design. The panel is constructed from individual rhombus-shaped profile strips, which are fitted between the existing posts.The product is available in various sizes and colour options and can be selected to match the specific carport. Made from Nordic spruce, the back panel impresses with its natural appearance and solid workmanship.Product featuresRhombus rear panel for retrofitting or adding to selected SKAN HOLZ carportsAvailable in various sizes and colour finishesModern rhombus design with an airy lookComprises individual rhombus-shaped profile strips to be screwed between the postsMade from Nordic spruceProvides additional privacy and wind protectionComplements the harmonious overall look of the carportContentsRhombus-shaped profile strips 2.8 x 5.6 cmPosts 12 x 12 cm60 cm H-post anchors made of galvanised flat steel for embedding in point foundations to be provided on siteAssembly materialsNotesAny carports, colour finishes, accessories or decorative items shown are not included in the scope of delivery. Illustrations may show examples of use and are intended to illustrate the assembled state. The scope of delivery is determined by the specific product variant selected.ConstructionThe construction is made of solid Nordic fir. We use technically-dried, solid spruce wood, scanned for flaws, sorted and weatherproofed by finger-joint bonding according to length. Small fissures, branches and slight twists reflect the character of the materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Backwall RhombusSuitable for post spacing of 550 cmNordic spruceColour-treated in anthraciteProvides additional privacy and protection from the wind
delivery time: 4-5 weeks
Storeroom of profiled siding material (for installation under a SKAN HOLZ carport)Profiled siding consists of loose tongued and grooved timber in 20 mm thickness, which is attached to one another and mounted between the posts.Product featuresWidth: 314 cmDepth: 317 cmHeight: 200 cmdoor (door clear opening 94 x 190 cm)Thickness: 20 mmpost including H-post anchorposts marked with red are available for carportsCustomer can easily adapt when installing into a carport with narrow passage widthMaterial: spruceGreen impregnatedConstructionThe construction is made of impregnated softwood. Spruce and pine wood, which is not technically-dried, acquires its greenish color from metal salts released by the impregnating agent. They protect wood against fungus and insect infestations, but do not contain UV protection. Impregnation gives wood higher residual moisture. Subsequent drying can lead to release of resin, twisting and formation of drying cracks, which pose no static disadvantage and rather reflect the natural materials used.Colour treatmentThe wooden parts in this kit have been treated at the factory with a water-based preservative. This means the kit can be assembled straight away upon delivery. To ensure the long-term preservation of the wooden surface, it is recommended that the wood be treated further after a sufficient drying and weathering period of approximately 2 to 3 sunny months.Before painting, the surface should be lightly sanded and cleaned. It is then recommended to apply two coats of a wood preservative suitable for outdoor use. Products with UV protection can help to reduce the visual ageing of the wood caused by weathering. Please follow the application instructions provided by the respective manufacturer.Regular maintenance and timely re-treatment help to keep the surface in good condition over the long term. The required maintenance intervals depend on the location, exposure to the elements and the coating system used.Storeroom C2314 x 317 cmProfiled siding materialGreen impregnated
delivery time: 3-4 weeks
Rear wall made of siding for installation in a SKAN HOLZ carportSiding consists of two layers of loose 20 mm thick formwork boards, which are only attached once the carport is completely assembled. It provides increased stability, privacy from the side and protection from e.g. wind or overgrown hedges.Product featuresWidth: 362 cmHeight: 330 cmFormwork thickness: 2 x 12 cmBuilt-in posts 12 x 12 cm, glulam spruceIncluding H-post anchorMaterial: Nordic spruceColour-treated in walnutPhoto galleryAny carports, colour treatment and decoration shown are not included in the scope of delivery. These are customer photos, which are intended to give you an impression of the installed state.ConstructionThe construction is made of solid Nordic fir. We use technically-dried, solid spruce wood, scanned for flaws, sorted and weatherproofed by finger-joint bonding according to length. Small fissures, branches and slight twists reflect the character of the materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Rear wall made of sidingNordic spruce, colour-treated in walnutHeight 330 cmInstallation posts 12 x 12 cm (glulam spruce)H-post anchor included
delivery time: 3-4 weeks
Rear wall made of siding for installation in a SKAN HOLZ carportSiding consists of two layers of loose 20 mm thick formwork boards, which are only attached once the carport is fully assembled. It provides increased stability, privacy from the side and protection from e.g. wind or overgrown hedges.Product featuresWidth: 362 cmHeight: 330 cmFormwork thickness: 2 x 12 cmBuilt-in posts 12 x 12 cm, glulam spruceIncluding H-post anchorMaterial: Nordic spruceColour-treated in light oakPhoto galleryAny carports, colour treatment and decoration shown are not included in the scope of delivery. These are customer photos, which are intended to give you an impression of the installed state.ConstructionThe construction is made of solid Nordic fir. We use technically-dried, solid spruce wood, scanned for flaws, sorted and weatherproofed by finger-joint bonding according to length. Small fissures, branches and slight twists reflect the character of the materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Rear wall made of sidingNordic spruce, colour-treated in light oakHeight 330 cmInstallation posts 12 x 12 cm (glulam spruce)H-post anchor included
delivery time: 3-4 weeks
Storeroom of profiled siding material (for installation under a SKAN HOLZ carport)Profiled siding consists of loose tongued and grooved timber in 20 mm thickness, which is attached to one another and mounted between the posts.Product featuresWidth: 314 cmDepth: 164 cmHeight: 200 cmdoor (door clear opening 94 x 190 cm)Thickness: 20 mmpost including H-post anchorposts marked with red are available for carportsCustomer can easily adapt when installing into a carport with narrow passage widthMaterial: sprucecolour-treated in walnutConstructionThe construction is made of impregnated softwood. Spruce and pine wood, which is not technically-dried, acquires its greenish color from metal salts released by the impregnating agent. They protect wood against fungus and insect infestations, but do not contain UV protection. Impregnation gives wood higher residual moisture. Subsequent drying can lead to release of resin, twisting and formation of drying cracks, which pose no static disadvantage and rather reflect the natural materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Storeroom C1314 x 164 cmProfiled siding materialColour-treated in walnut
delivery time: 4-5 weeks
Storeroom of profiled siding material (for installation under a SKAN HOLZ carport)Profiled siding consists of loose tongued and grooved timber in 20 mm thickness, which is attached to one another and mounted between the posts.Product featuresWidth: 378 cmDepth: 317 cmHeight: 200 cmdoor (door clear opening 94 x 190 cm)Thickness: 20 mmpost including H-post anchorposts marked with red are available for carportsCustomer can easily adapt when installing into a carport with narrow passage widthMaterial: spruceGreen impregnatedConstructionThe construction is made of impregnated softwood. Spruce and pine wood, which is not technically-dried, acquires its greenish color from metal salts released by the impregnating agent. They protect wood against fungus and insect infestations, but do not contain UV protection. Impregnation gives wood higher residual moisture. Subsequent drying can lead to release of resin, twisting and formation of drying cracks, which pose no static disadvantage and rather reflect the natural materials used.Colour treatmentThe wooden parts in this kit have been treated at the factory with a water-based preservative. This means the kit can be assembled straight away upon delivery. To ensure the long-term preservation of the wooden surface, it is recommended that the wood be treated further after a sufficient drying and weathering period of approximately 2 to 3 sunny months.Before painting, the surface should be lightly sanded and cleaned. It is then recommended to apply two coats of a wood preservative suitable for outdoor use. Products with UV protection can help to reduce the visual ageing of the wood caused by weathering. Please follow the application instructions provided by the respective manufacturer.Regular maintenance and timely re-treatment help to keep the surface in good condition over the long term. The required maintenance intervals depend on the location, exposure to the elements and the coating system used.Storeroom C4378 x 317 cmProfiled siding materialGreen impregnated
delivery time: 3-4 weeks
Storeroom of profiled siding material (for installation under a SKAN HOLZ carport)Profiled siding consists of loose tongued and grooved timber in 20 mm thickness, which is attached to one another and mounted between the posts.Product featuresWidth: 275 cmDepth: 317 cmHeight: 200 cmdoor (door clear opening 94 x 190 cm)Thickness: 20 mmpost including H-post anchorposts marked with red are available for carportsCustomer can easily adapt when installing into a carport with narrow passage widthMaterial: spruceGreen impregnatedConstructionThe construction is made of impregnated softwood. Spruce and pine wood, which is not technically-dried, acquires its greenish color from metal salts released by the impregnating agent. They protect wood against fungus and insect infestations, but do not contain UV protection. Impregnation gives wood higher residual moisture. Subsequent drying can lead to release of resin, twisting and formation of drying cracks, which pose no static disadvantage and rather reflect the natural materials used.Colour treatmentThe wooden parts in this kit have been treated at the factory with a water-based preservative. This means the kit can be assembled straight away upon delivery. To ensure the long-term preservation of the wooden surface, it is recommended that the wood be treated further after a sufficient drying and weathering period of approximately 2 to 3 sunny months.Before painting, the surface should be lightly sanded and cleaned. It is then recommended to apply two coats of a wood preservative suitable for outdoor use. Products with UV protection can help to reduce the visual ageing of the wood caused by weathering. Please follow the application instructions provided by the respective manufacturer.Regular maintenance and timely re-treatment help to keep the surface in good condition over the long term. The required maintenance intervals depend on the location, exposure to the elements and the coating system used.Storeroom C8275 x 317 cmProfiled siding materialGreen impregnated
delivery time: 3-4 weeks
Rear wall made of siding for installation in a SKAN HOLZ carportSiding consists of two layers of loose 20 mm thick formwork boards, which are only attached once the carport is fully assembled. It provides increased stability, privacy from the side and protection from e.g. wind or overgrown hedges.Product featuresWidth: 362 cmHeight: 330 cmFormwork thickness: 2 x 12 cmBuilt-in posts 12 x 12 cm, glulam spruceIncluding H-post anchorMaterial: Nordic spruceColour-treated in anthracitePhoto galleryAny carports, colour treatment and decoration shown are not included in the scope of delivery. These are customer photos, which are intended to give you an impression of the installed state.ConstructionThe construction is made of solid Nordic fir. We use technically-dried, solid spruce wood, scanned for flaws, sorted and weatherproofed by finger-joint bonding according to length. Small fissures, branches and slight twists reflect the character of the materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Rear wall made of sidingNordic spruce, colour-treated in anthraciteHeight 330 cmInstallation posts 12 x 12 cm (glulam spruce)H-post anchor included
delivery time: 3-4 weeks
Backwall of siding for installation in a SKAN HOLZ CarportSiding consists of loose boarding in 20 mm thickness, and is not installed until the carport has been completely erected. It provides for increased stability, privacy shield from the side, and protection from wind and overgrown hedges.Product featuresWidth: 550 cmHeight: 180 cmthickness siding: 2 x 12 cmincluding H-post anchorMaterial: nordic sprucecolour-treated in light oakPhoto galleryAny illustrated terrace roofs, colour treatment and decoration are not included in scope of supply. This involves customer photos, which are to provide you with an impression of the installed condition.ConstructionThe construction is made of solid Nordic fir. We use technically-dried, solid spruce wood, scanned for flaws, sorted and weatherproofed by finger-joint bonding according to length. Small fissures, branches and slight twists reflect the character of the materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Backwall, nordic sprucePanels with vertical slatsSuitable for post spacing of 550 cmColour-treated in light oak
delivery time: 4-5 weeks
Rear wall made of siding for installation in a SKAN HOLZ carportSiding consists of two layers of loose 20 mm thick formwork boards, which are only attached once the carport is completely assembled. It provides increased stability, privacy from the side and protection from e.g. wind or overgrown hedges.Product featuresWidth: 362 cmHeight: 330 cmFormwork thickness: 2 x 12 cmBuilt-in posts 12 x 12 cm, glulam spruceIncluding H-post anchorMaterial: Nordic spruceColour-treated in whitePhoto galleryAny carports, colour treatment and decoration shown are not included in the scope of delivery. These are customer photos, which are intended to give you an impression of the installed state.ConstructionThe construction is made of solid Nordic fir. We use technically-dried, solid spruce wood, scanned for flaws, sorted and weatherproofed by finger-joint bonding according to length. Small fissures, branches and slight twists reflect the character of the materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Rear wall made of sidingNordic spruce, colour-treated in whiteHeight 330 cmInstallation posts 12 x 12 cm (glulam spruce)H-post anchor included
delivery time: 3-4 weeks
Backwall of siding for installation in a SKAN HOLZ CarportSiding consists of loose boarding in 20 mm thickness, and is not installed until the carport has been completely erected. It provides for increased stability, privacy shield from the side, and protection from wind and overgrown hedges.Product featuresWidth: 550 cmHeight: 180 cmthickness siding: 2 x 12 cmincluding H-post anchorMaterial: nordic sprucecolour-treated in walnutPhoto galleryAny illustrated terrace roofs, colour treatment and decoration are not included in scope of supply. This involves customer photos, which are to provide you with an impression of the installed condition.ConstructionThe construction is made of solid Nordic fir. We use technically-dried, solid spruce wood, scanned for flaws, sorted and weatherproofed by finger-joint bonding according to length. Small fissures, branches and slight twists reflect the character of the materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Backwall, nordic sprucePanels with vertical slatsSuitable for post spacing of 550 cmColour-treated in walnut
delivery time: 4-5 weeks
Rear wall made of siding for installation in a SKAN HOLZ carportSiding consists of two layers of loose 20 mm thick formwork boards, which are only attached once the carport is fully assembled. It provides increased stability, privacy from the side and protection from e.g. wind or overgrown hedges.Product featuresWidth: 362 cmHeight: 330 cmFormwork thickness: 2 x 12 cmBuilt-in posts 12 x 12 cm, glulam spruceIncluding H-post anchorMaterial: Nordic spruceColour-treated in slate greyPhoto galleryAny carports, colour treatment and decoration shown are not included in the scope of delivery. These are customer photos, which are intended to give you an impression of the installed state.ConstructionThe construction is made of solid Nordic fir. We use technically-dried, solid spruce wood, scanned for flaws, sorted and weatherproofed by finger-joint bonding according to length. Small fissures, branches and slight twists reflect the character of the materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Rear wall made of sidingNordic spruce, colour-treated in slate greyHeight 330 cmInstallation posts 12 x 12 cm (glulam spruce)H-post anchor included
delivery time: 3-4 weeks
Storeroom of profiled siding material (for installation under a SKAN HOLZ carport)Profiled siding consists of loose tongued and grooved timber in 20 mm thickness, which is attached to one another and mounted between the posts.Product featuresWidth: 378 cmDepth: 164 cmHeight: 200 cmdoor (door clear opening 94 x 190 cm)Thickness: 20 mmpost including H-post anchorposts marked with red are available for carportsCustomer can easily adapt when installing into a carport with narrow passage widthMaterial: sprucecolour-treated in walnutConstructionThe construction is made of impregnated softwood. Spruce and pine wood, which is not technically-dried, acquires its greenish color from metal salts released by the impregnating agent. They protect wood against fungus and insect infestations, but do not contain UV protection. Impregnation gives wood higher residual moisture. Subsequent drying can lead to release of resin, twisting and formation of drying cracks, which pose no static disadvantage and rather reflect the natural materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Storeroom C3378 x 164 cmProfiled siding materialColour-treated in walnut
delivery time: 4-5 weeks
Storeroom of profiled siding material (for installation under a SKAN HOLZ carport)Profiled siding consists of loose tongued and grooved timber in 20 mm thickness, which is attached to one another and mounted between the posts.Product featuresWidth: 314 cmDepth: 164 cmHeight: 200 cmdoor (door clear opening 94 x 190 cm)Thickness: 20 mmpost including H-post anchorposts marked with red are available for carportsCustomer can easily adapt when installing into a carport with narrow passage widthMaterial: sprucecolour-treated in slate greyConstructionThe construction is made of impregnated softwood. Spruce and pine wood, which is not technically-dried, acquires its greenish color from metal salts released by the impregnating agent. They protect wood against fungus and insect infestations, but do not contain UV protection. Impregnation gives wood higher residual moisture. Subsequent drying can lead to release of resin, twisting and formation of drying cracks, which pose no static disadvantage and rather reflect the natural materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Storeroom C1314 x 164 cmProfiled siding materialColour-treated in slate grey
delivery time: 4-5 weeks
Roof greening not only looks good, it also provides many benefits. This roofing protects against the elements, reduces the noise of precipitation, and looks great in a natural environment.Make sure to water regularly during the growth phase (depending on environmental influences). The substrate must be kept sufficiently moist until the roots are established.Included in delivery:Sedum sprouts (mix of 3-4 types, which vary according to time of year)SubstrateFilter fiberstorage mats (Biodrain)Aluminium collection stripNote:Please be aware that roof greening adds a load of approx. 50 kg/m². The structure must have capacity to bear this weight. It may become necessary to mount the increased snow load. It is optionally available. Roof greening is separately supplied and can only be delivered in Germany.Roof greening system308 x 550 cmIncluding substrateincluding filter fiberIncludinig storage mats (Biodrain)
delivery time: 3-4 weeks
Backwall of siding for installation in a SKAN HOLZ CarportSiding consists of loose boarding in 20 mm thickness, and is not installed until the carport has been completely erected. It provides for increased stability, privacy shield from the side, and protection from wind and overgrown hedges.Product featuresWidth: 550 cmHeight: 180 cmthickness siding: 2 x 12 cmincluding H-post anchorMaterial: nordic sprucecolour-treated in slate greyPhoto galleryAny illustrated terrace roofs, colour treatment and decoration are not included in scope of supply. This involves customer photos, which are to provide you with an impression of the installed condition.ConstructionThe construction is made of solid Nordic fir. We use technically-dried, solid spruce wood, scanned for flaws, sorted and weatherproofed by finger-joint bonding according to length. Small fissures, branches and slight twists reflect the character of the materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Backwall, nordic sprucePanels with vertical slatsSuitable for post spacing of 550 cmColour-treated in slate grey
delivery time: 4-5 weeks
Backwall of siding for installation in a SKAN HOLZ CarportSiding consists of loose boarding in 20 mm thickness, and is not installed until the carport has been completely erected. It provides for increased stability, privacy shield from the side, and protection from wind and overgrown hedges.Product featuresWidth: 550 cmHeight: 180 cmthickness siding: 2 x 12 cmincluding H-post anchorMaterial: nordic sprucecolour-treated in anthracitePhoto galleryAny illustrated terrace roofs, colour treatment and decoration are not included in scope of supply. This involves customer photos, which are to provide you with an impression of the installed condition.ConstructionThe construction is made of solid Nordic fir. We use technically-dried, solid spruce wood, scanned for flaws, sorted and weatherproofed by finger-joint bonding according to length. Small fissures, branches and slight twists reflect the character of the materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Backwall, nordic sprucePanels with vertical slatsSuitable for post spacing of 550 cmColour-treated in anthracite
delivery time: 4-5 weeks
Backwall of siding for installation in a SKAN HOLZ CarportSiding consists of loose boarding in 20 mm thickness, and is not installed until the carport has been completely erected. It provides for increased stability, privacy shield from the side, and protection from wind and overgrown hedges.Product featuresWidth: 550 cmHeight: 180 cmthickness siding: 2 x 12 cmincluding H-post anchorMaterial: nordic sprucecolour-treated in whitePhoto galleryAny illustrated terrace roofs, colour treatment and decoration are not included in scope of supply. This involves customer photos, which are to provide you with an impression of the installed condition.ConstructionThe construction is made of solid Nordic fir. We use technically-dried, solid spruce wood, scanned for flaws, sorted and weatherproofed by finger-joint bonding according to length. Small fissures, branches and slight twists reflect the character of the materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Backwall, nordic sprucePanels with vertical slatsSuitable for post spacing of 550 cmColour-treated in white
delivery time: 4-5 weeks
Storeroom of profiled siding material (for installation under a SKAN HOLZ carport)Profiled siding consists of loose tongued and grooved timber in 20 mm thickness, which is attached to one another and mounted between the posts.Product featuresWidth: 573 cmDepth: 164 cmHeight: 200 cmdoor (door clear opening 94 x 190 cm)Thickness: 20 mmpost including H-post anchorposts marked with red are available for carportsCustomer can easily adapt when installing into a carport with narrow passage widthMaterial: spruceGreen impregnatedConstructionThe construction is made of impregnated softwood. Spruce and pine wood, which is not technically-dried, acquires its greenish color from metal salts released by the impregnating agent. They protect wood against fungus and insect infestations, but do not contain UV protection. Impregnation gives wood higher residual moisture. Subsequent drying can lead to release of resin, twisting and formation of drying cracks, which pose no static disadvantage and rather reflect the natural materials used.Colour treatmentThe wooden parts in this kit have been treated at the factory with a water-based preservative. This means the kit can be assembled straight away upon delivery. To ensure the long-term preservation of the wooden surface, it is recommended that the wood be treated further after a sufficient drying and weathering period of approximately 2 to 3 sunny months.Before painting, the surface should be lightly sanded and cleaned. It is then recommended to apply two coats of a wood preservative suitable for outdoor use. Products with UV protection can help to reduce the visual ageing of the wood caused by weathering. Please follow the application instructions provided by the respective manufacturer.Regular maintenance and timely re-treatment help to keep the surface in good condition over the long term. The required maintenance intervals depend on the location, exposure to the elements and the coating system used.Storeroom C5573 x 164 cmProfiled siding materialGreen impregnated
delivery time: 3-4 weeks
Storeroom of profiled siding material (for installation under a SKAN HOLZ carport)Profiled siding consists of loose tongued and grooved timber in 20 mm thickness, which is attached to one another and mounted between the posts.Product featuresWidth: 275 cmDepth: 164 cmHeight: 200 cmdoor (door clear opening 94 x 190 cm)Thickness: 20 mmpost including H-post anchorposts marked with red are available for carportsCustomer can easily adapt when installing into a carport with narrow passage widthMaterial: sprucecolour-treated in walnutConstructionThe construction is made of impregnated softwood. Spruce and pine wood, which is not technically-dried, acquires its greenish color from metal salts released by the impregnating agent. They protect wood against fungus and insect infestations, but do not contain UV protection. Impregnation gives wood higher residual moisture. Subsequent drying can lead to release of resin, twisting and formation of drying cracks, which pose no static disadvantage and rather reflect the natural materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Storeroom C7275 x 164 cmProfiled siding materialColour-treated in walnut
delivery time: 4-5 weeks