Carport Emsland 613 x 604 cm with EPDM roof, colour pre-treated white

Siding for installation in a SKAN HOLZ CarportSiding consists of loose boarding in 20 mm thickness, and is not installed until the carport has been completely erected. It provides for increased stability, privacy shield from the side, and protection from wind and overgrown hedges.Product featuresWidth: 230 cmHeight: 180 cmthickness siding: 2 x 12 cmMaterial: nordic sprucecolour-treated in whitePhoto galleryAny illustrated terrace roofs, colour treatment and decoration are not included in scope of supply. This involves customer photos, which are to provide you with an impression of the installed condition.ConstructionThe construction is made of solid Nordic fir. We use technically-dried, solid spruce wood, scanned for flaws, sorted and weatherproofed by finger-joint bonding according to length. Small fissures, branches and slight twists reflect the character of the materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Sidewall, nordic sprucePanels with vertical slatsSuitable for post spacing of 230 cmColour-treated in white

Siding for installation in a SKAN HOLZ CarportSiding consists of loose boarding in 20 mm thickness, and is not installed until the carport has been completely erected. It provides for increased stability, privacy shield from the side, and protection from wind and overgrown hedges.Product featuresWidth: 230 cmHeight: 220 cmthickness siding: 2 x 12 cmMaterial: nordic sprucecolour-treated in whitePhoto galleryAny illustrated terrace roofs, colour treatment and decoration are not included in scope of supply. This involves customer photos, which are to provide you with an impression of the installed condition.ConstructionThe construction is made of solid Nordic fir. We use technically-dried, solid spruce wood, scanned for flaws, sorted and weatherproofed by finger-joint bonding according to length. Small fissures, branches and slight twists reflect the character of the materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Sidewall, nordic sprucePanels with vertical slatsSuitable for post spacing of 230 cmColour-treated in white

Backwall of siding for installation in a SKAN HOLZ CarportSiding consists of loose boarding in 20 mm thickness, and is not installed until the carport has been completely erected. It provides for increased stability, privacy shield from the side, and protection from wind and overgrown hedges.Product featuresWidth: 550 cmHeight: 180 cmthickness siding: 2 x 12 cmincluding H-post anchorMaterial: nordic sprucecolour-treated in whitePhoto galleryAny illustrated terrace roofs, colour treatment and decoration are not included in scope of supply. This involves customer photos, which are to provide you with an impression of the installed condition.ConstructionThe construction is made of solid Nordic fir. We use technically-dried, solid spruce wood, scanned for flaws, sorted and weatherproofed by finger-joint bonding according to length. Small fissures, branches and slight twists reflect the character of the materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Backwall, nordic sprucePanels with vertical slatsSuitable for post spacing of 550 cmColour-treated in white

Do you need longer posts?Order the post extension for your terrace roof or carport of glued laminate. The posts in the building kits are then replaced with longer posts.Product featuresThickness: 12 x 12 cmMaterial: glulam, sprucecolour-treated in whiteAttention: the surcharge applies per post, and they can only be ordered directly with the carport/terrace roof.Post extension 12x12cm in running meters12 x 12 cmGlued laminateColour-treated in white

Backwall of siding for installation in a SKAN HOLZ CarportSiding consists of loose boarding in 20 mm thickness, and is not installed until the carport has been completely erected. It provides for increased stability, privacy shield from the side, and protection from wind and overgrown hedges.Product featuresWidth: 550 cmHeight: 220 cmthickness siding: 2 x 12 cmincluding H-post anchorMaterial: nordic sprucecolour-treated in whitePhoto galleryAny illustrated terrace roofs, colour treatment and decoration are not included in scope of supply. This involves customer photos, which are to provide you with an impression of the installed condition.ConstructionThe construction is made of solid Nordic fir. We use technically-dried, solid spruce wood, scanned for flaws, sorted and weatherproofed by finger-joint bonding according to length. Small fissures, branches and slight twists reflect the character of the materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Backwall, nordic sprucePanels with vertical slatsSuitable for post spacing of 550 cmColour-treated in white

Comfortable entry and exit of carport by mounting one or two round arches. The first post is eliminated by mounting the round arch.Product featuresThickness: 11,5 x 12 cmMaterial: glulam, sprucecolour-treated in whitecan be mounted left or rightfor carports with an entrance height of 220 cmFor static reasons, cannot be mounted on saddle-roof carports, increased snow load, and post extensions.Entrance arch 11,5x12cmGlued laminateColour-treated in white

The SKAN HOLZ snow load extension consists of additional rafters that you mount between the existing roof rafters. This reduces the rafter spacing of the carport and increases the overall load-bearing capacity. The number and size of the rafters varies depending on the carport.The snow load increase raises the snow load of the carport to 2.0 kN/m².This snow load increase contains 4 additional rafters and is suitable for the following models:Emsland carport 609 (613) x 604 cmWendland carport 630 x 637 cmSpessart carport 611 x 604 cmColour-treated in whitePlease note:The snow load cannot be retrofitted to the carports. Please check the snow load limit required in your residential area before assembly.ConstructionThe construction is made of glued laminate timber, consisting of several dried layers, attached to one another with finger-jointing. They are glued onto one another for weather-resistance. This results in a load-bearing beam which is more resistant to warping and less prone to fissures than naturally grown wood.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Snow load increase to sk=2.00 kN/m²Glued laminated timber, Colour-treated in whiteSuitable for Emsland carport 609 (613) x 604 cmSuitable for Wendland carport 630 x 637 cmSuitable for carport Spessart 611 x 604 cm

Roof greening not only looks good, it also provides many benefits. This roofing protects against the elements, reduces the noise of precipitation, and looks great in a natural environment.Make sure to water regularly during the growth phase (depending on environmental influences). The substrate must be kept sufficiently moist until the roots are established.Included in delivery:Sedum sprouts (mix of 3-4 types, which vary according to time of year)SubstrateFilter fiberstorage mats (Biodrain)Aluminium collection stripNote:Please be aware that roof greening adds a load of approx. 50 kg/m². The structure must have capacity to bear this weight. It may become necessary to mount the increased snow load. It is optionally available. Roof greening is separately supplied and can only be delivered in Germany.Roof greening system609 x 600 cmIncluding substrateincluding filter fiberIncludinig storage mats (Biodrain)

Backwall Rhombus for installation in SKAN HOLZ carportThe walls consist of Rhombus sectional strips, loosely supplied, which are screwed between the posts.Product featuresWidth: 550 cmHeight: 160 cmthickness battens: 2,8 x 5,6 cmthickness posts: 12 x 12 cmincluding H-post anchorMaterial: nordic sprucecolour-treated in whitePhoto galleryAny illustrated terrace roofs, colour treatment and decoration are not included in scope of supply. This involves customer photos, which are to provide you with an impression of the installed condition.ConstructionThe construction is made of solid Nordic fir. We use technically-dried, solid spruce wood, scanned for flaws, sorted and weatherproofed by finger-joint bonding according to length. Small fissures, branches and slight twists reflect the character of the materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Backwall RhombusSuitable for post spacing of 550 cmNordic spruceColour-treated in white

Sidewall Rhombus for installation in SKAN HOLZ carportThe walls consist of Rhombus sectional strips, loosely supplied, which are screwed between the posts.Product featuresWidth: 230 cmHeight: 160 cmthickness battens: 2,8 x 5,6 cmMaterial: nordic sprucecolour-treated in whitePhoto galleryAny illustrated terrace roofs, colour treatment and decoration are not included in scope of supply. This involves customer photos, which are to provide you with an impression of the installed condition.ConstructionThe construction is made of solid Nordic fir. We use technically-dried, solid spruce wood, scanned for flaws, sorted and weatherproofed by finger-joint bonding according to length. Small fissures, branches and slight twists reflect the character of the materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Sidewall RhombusSuitable for post spacing of 230 cmNordic spruceColour-treated in white

Downpipe flap with strainerThe downpipe valve with integrated strainer enables rainwater to be diverted specifically from the downpipe and is ideal for filling rain barrels, cisterns or other collection tanks. The built-in strainer reduces the ingress of leaves, dirt and other coarse debris, thereby helping to ensure better water quality.Thanks to the practical flap mechanism, the water flow can be diverted as required or allowed to pass directly through the downpipe. The robust metal construction with a weather-resistant coating ensures a long service life and an attractive appearance on the building.Technical featuresRainwater downpipe flap with strainer 1 additional pipe clamp Material: Metal Colour: Anthracite Diameter: 80 mmProduct benefits at a glanceIntegrated strainer to reduce leaves and coarse dirt particles Targeted diversion of rainwater into rain barrels or collection tanks Easy switching between water drainage and flow-through mode Robust metal construction for high stability Weather-resistant finish for long-term outdoor use Easy integration into existing downpipe systems Low-maintenance structureThe rainwater pipe valve with integrated strainer is fitted directly into the existing downpipe and allows rainwater to be diverted as required into a rainwater buttrug or another collection tank.Easy to use✅ Shorten the downpipe to the desired length✅ Fit an additional pipe clamp to the longer section of pipe✅ Insert and align the rainwater pipe valve✅ Connect the rainwater tank✅ Open or close the flap as required✅ Clean the built-in strainer regularly to ensure optimum water qualityHandy rainwater pipe flapwith built-in sieveIncluding an additional pipe clampCoated in anthraciteEasy integration into the existing downpipe system