Breisgau carport, 609 x 840 cm, with EPDM roof and storeroom, white

SKAN HOLZ side panel made from profiled cladding for carportsThe side panel made from profiled cladding by SKAN HOLZ is a practical and visually appealing addition to selected carports. It provides additional privacy. The panel is constructed from individual profiled timber boards with a tongue-and-groove profile, which are fitted between the existing posts.The product is available in a range of colours and can be selected to match the respective carport. Made from Nordic spruce, the side panel impresses with its natural appearance and solid workmanship.Product featuresSide panel for retrofitting or adding to selected SKAN HOLZ carportsAvailable in a range of coloursMade from individual profiled timber boards to be screwed between the postsMade from Nordic spruceProvides additional privacy and wind protectionComplements the harmonious overall look of the carportNotesAny carports, colour treatments, accessories or decorative items shown are not included in the scope of delivery. Illustrations may show examples of use and are intended to illustrate the assembled state. The scope of delivery is determined by the specific product variant selected.Side wall made of profiled formworkWidth 230 cm x Height 200 cmSpruce, colour-treated in whiteSuitable for post spacing of up to 230 cmProvides additional privacy and protection from the wind

SKAN HOLZ Rhombus Side Panel for CarportsThe Rhombus side panel from SKAN HOLZ is a practical and visually appealing addition to selected carports. It provides additional privacy and gives the carport a modern, open rhombus design. The wall is constructed from individual rhombus-shaped profile strips, which are fitted between the existing posts.The product is available in a range of colours and can be selected to match the specific carport. Made from Nordic spruce, the side panel impresses with its natural appearance and solid workmanship.Product featuresRhombus side panel for retrofitting or adding to selected SKAN HOLZ carportsAvailable in a range of colour finishesModern rhombus design with an airy lookComprising individual 2.8 x 5.6 cm rhombus-shaped profile strips to be screwed between the postsMade from Nordic spruceProvides additional privacy and wind protectionComplements the harmonious overall look of the carportNotesAny carports, colour finishes, accessories or decorative items shown are not included in the scope of delivery. Illustrations may show examples of use and are intended to illustrate the assembled state. The scope of delivery is determined by the specific product variant selected.ConstructionThe construction is made of solid Nordic fir. We use technically-dried, solid spruce wood, scanned for flaws, sorted and weatherproofed by finger-joint bonding according to length. Small fissures, branches and slight twists reflect the character of the materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Sidewall RhombusSuitable for post spacing of 230 cmNordic spruceColour-treated in whiteProvides additional privacy and protection from the wind

Do you need longer posts?Order the post extension for your terrace roof or carport of glued laminate. The posts in the building kits are then replaced with longer posts.Product featuresThickness: 12 x 12 cmMaterial: glulam, sprucecolour-treated in whiteAttention: the surcharge applies per post, and they can only be ordered directly with the carport/terrace roof.Post extension 12x12cm in running meters12 x 12 cmGlued laminateColour-treated in white

Comfortable entry and exit of carport by mounting one or two round arches. The first post is eliminated by mounting the round arch.Product featuresThickness: 11,5 x 12 cmMaterial: glulam, sprucecolour-treated in whitecan be mounted left or rightfor carports with an entrance height of 220 cmFor static reasons, cannot be mounted on saddle-roof carports, increased snow load, and post extensions.Entrance arch 11,5x12cmGlued laminateColour-treated in white

The SKAN HOLZ snow load reinforcement consists of additional rafters which you fit between the existing roof rafters. This reduces the rafter spacing of the carport, thereby increasing its overall load-bearing capacity. The number and size of the rafters vary depending on the carport.The snow load increases the carport’s snow load capacity to 2.0 kN/m².This snow load reinforcement kit contains 6 additional rafters and is compatible with the following models:Carport Emsland 609 (613) x 846 cmBreisgau carport 609 x 840 cmCarport Wendland 630 x 879 cmSpessart carport 611 x 846 cmColour-treated in whitePleasenote:The snow load cannot be retrofitted to these carports. Please check the required snow load limit for your residential area before assembly.ConstructionThe construction is made of glued laminate timber, consisting of several dried layers, attached to one another with finger-jointing. They are glued onto one another for weather-resistance. This results in a load-bearing beam which is more resistant to warping and less prone to fissures than naturally grown wood.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Snow load increase to sk=2.00 kN/m²Suitable for the Emsland carport (609 (613) x 846 cm)Suitable for the Wendland carport (630 x 879 cm)Suitable for the Breisgau carport (609 x 840 cm)Suitable for the Spessart carport (611 x 846 cm)

Roof greening not only looks good, it also provides many benefits. This roofing protects against the elements, reduces the noise of precipitation, and looks great in a natural environment.Make sure to water regularly during the growth phase (depending on environmental influences). The substrate must be kept sufficiently moist until the roots are established.Included in delivery:Sedum sprouts (mix of 3-4 types, which vary according to time of year)SubstrateFilter fiberstorage mats (Biodrain)Aluminium collection stripNote:Please be aware that roof greening adds a load of approx. 50 kg/m². The structure must have capacity to bear this weight. It may become necessary to mount the increased snow load. It is optionally available. Roof greening is separately supplied and can only be delivered in Germany.Roof greening system609 x 840 cmIncluding substrateincluding filter fiberIncludinig storage mats (Biodrain)

Downpipe flap with strainerThe downpipe valve with integrated strainer enables rainwater to be diverted specifically from the downpipe and is ideal for filling rain barrels, cisterns or other collection tanks. The built-in strainer reduces the ingress of leaves, dirt and other coarse debris, thereby helping to ensure better water quality.Thanks to the practical flap mechanism, the water flow can be diverted as required or allowed to pass directly through the downpipe. The robust metal construction with a weather-resistant coating ensures a long service life and an attractive appearance on the building.Technical featuresRainwater downpipe flap with strainer 1 additional pipe clamp Material: Metal Colour: Anthracite Diameter: 80 mmProduct benefits at a glanceIntegrated strainer to reduce leaves and coarse dirt particles Targeted diversion of rainwater into rain barrels or collection tanks Easy switching between water drainage and flow-through mode Robust metal construction for high stability Weather-resistant finish for long-term outdoor use Easy integration into existing downpipe systems Low-maintenance structureThe rainwater pipe valve with integrated strainer is fitted directly into the existing downpipe and allows rainwater to be diverted as required into a rainwater buttrug or another collection tank.Easy to use✅ Shorten the downpipe to the desired length✅ Fit an additional pipe clamp to the longer section of pipe✅ Insert and align the rainwater pipe valve✅ Connect the rainwater tank✅ Open or close the flap as required✅ Clean the built-in strainer regularly to ensure optimum water qualityHandy rainwater pipe flapwith built-in sieveIncluding an additional pipe clampCoated in anthraciteEasy integration into the existing downpipe system